FPV Mario AIO
OpenIPC Wiki
OpenIPC AIO “Mario”
https://store.openipc.org/OpenIPC-AIO-Mario-v1-0-p633320808
Remove the lens cover film befor use
The Mario camera case with 4x M1.2 screws.
Side mount holes are M2 x2 screw thread.
Install atennas for AIO.
LED function
Red glimmering Power on with Battery
Red Wired linked
Blue flash RF transmitter
Green TBD
Board Size 30mmx32mm with 4*M2 mount holes.
Heat Sink with 20mmx20mm mount holes.
Power Section
Power input:
2S-6S
The on board dualway BEC Capacity:
RF BEC on board is up to 3A 5V output
MSIC BEC on board is up to 2A 5V output
enter uboot use uart device connect to top of AIO board(R0,T0)pad.
How to get lower voltage input for DC input
AIO power supply from 2s-3S battery needed more current and required 4wires connected, but higher voltage 4S+ may works 2wire connection.
Remove two resistors then you can get input as low as 5.4V input available.
Connect usb debug port
Plug USB cable to connect AIO and PC first, then power on DC, or usb power only.
If there are unknown USB devices in the computer, the following corechip-sr9900 drivers need to be installed.
Operations on Mac OS
Autosetup in windows
Please download Auto_Set_Mario_CDC.zip file, unzip it and run as administrator.
or setting manually as follows:
go to control panel- internet -network:
find a usb2.0 to fast Ethernet Adapter
set this card ipv4 address to 192.168.1.11 mask:255.255.255.0
apply
then open ssh to connect AIO address:192.168.1.10
user
password:12345How to get internet for AIO
1.Open network connections on you windows, right click your main network adapter properties---Sharing: Allow other network users choose USB CDC
Apply,then the CDC ethernet will got a ip address 192.168.137.1 automaticlly
open admin terminal
using arp -a to find AIO’s IP
here 192.168.137.147 is my AIO’s ip address.
open ssh connect to AIO,Done.
Now you can use sysupgrade -r -k -n —force_ver to update your firmware.
Upgrade firmware
Update firmware possible via SD card or just use win scp drug the rootfs and kernel files to /tmp
sysupgrade -n -z --kernel=/tmp/uImage.ssc338q --rootfs=/tmp/rootfs.squashfs.ssc338qYou can download firmware via the link that is used for online updates.
You can also read the current discussions and suggestions here:
Or just use the configurator - https://github.com/OpenIPC/configurator
RF section
RF antenna characteristics
Default Antenna is ANT1 for 1T1R, ANT0+ANT1 is 2T2R
Reconmand RF setting
RF Power max 18dbm for onbard PA input. For 1T1R rf setting range: 1-63 firmware update to latest! stbc=0,ldpc=0 Recommand RF power value < 45
MCS index 1,3(0-7 is 1T1R, 8+ is 2T2R)
Video bitrate:4096 /8192/12688(mcs 3+)
when use stbc=1,ldpc=1 recommand rf power setting for MCS3 from 8-15 for test.
Keep RF power < = 15 when on bench test(when only usb connect)
SD solt for Air camera record
on bench test or debug is disable the record function defaultly
To enable the recording function set (record value)true in majestic.yaml
SD card must insert before Powering.
On board heat sink and cooling fan:
cooling fan out put power up to 500mA max
all heat sink mount holes are M2 screws thread.
Extend connector**
NOTE
USB only for debug mode, when DC power only, the cdc ethernet works in sleep mode to save energy.
USB power only mode Power limited 5W input.
Upgrade Firmware to Ruby FPV
plug usb cable and setting cdc ethernet ipv4: 192.168.1.11 255.255.255.0
use winscp drag unzip files to /tmp
use ssh login and copy following command:
sysupgrade —kernel=/tmp/uImage.ssc338q —rootfs=/tmp/rootfs.squashfs.ssc338q -z -n
after update and reboot
use ssh login and set command:
fw_setenv sensor imx335 && fw_setenv upgrade https://github.com/OpenIPC/firmware/releases/download/latest/openipc.ssc338q-nor-rubyfpv.tgz && reboot